Morris Book Tutorial

First I need to clarify definitions:
One BLOCK = the 6" CQJP square as I finished it...
One PAGE  = two (2) blocks back-to-back.
One SECTION = two pages sewn together..

I ended the Crazy Quilt Journal Project 2012 with 16 blocks... I wasn't as careful as I should have been and there was considerable size difference between the largest and smallest blocks...  Rather than cut them all down to the size of the smallest block (which was certainly a viable option) I chose to add a border to all the blocks and then trim them to  common size...




I then cut a light piece of felt to the common size of the blocks ... A piece of lightweight cotton batting would have worked just as well.  I wanted this filler between the blocks to give the page some body... no limp pages for me....  At the same time I cut two pieces of heavy interfacing for the covers...  They need to cut about 1/2" larger on the outside edges....not on the side facing the spine of the book.




Then I sewed a strip of 2 1/2" binding around each page (2 blocks back-to-back) by machine...  I made the binding out of material to coordinate with the blocks... I highly recommend making a BIAS binding.... it is much more pliable and forgiving than binding cut on grain. There are numerous sites (and even videos) which show how to do this but I really liked this site... http://cynthiashaffer.typepad.com/blog/2011/05/turning-a-corner-making-a-point-binding-tutorial.html.  She did a much better job of explaining this step than I every could.

And then I neatly turned the binding to the back, pressed it, and sewed it by hand..













When all the pages were bound I sewed two pages together to make a SECTION!







Then I cut the spine a little wider than I thought I would need from the same heavy duty interfacing.  I marked lines about 1/2" apart... I cover one side with coordinating fabric by using double sided interfacing...







 I then sewed down the lines with a bobbin thread that would show easily on the fabric.










Then by hand, I sewed each section to a line....in order of course..








When open you can see that the sections are about 1/2" apart on the spine but because the pages are so thick that is necessary for the book to open properly and lay flat.




At this point (without covers) you can see how it looks...  There are 3 SECTIONS of two PAGES each.   So there are 12 blocks for the inside to the book,

I trimmed the spine to just leave enough seam allowance to add the covers and covered it with a piece of felt...  I then assembled the covers exactly like I did the pages except I added both the felt and the interfacing.


I then sewed the covers to the spine by hand.  This was the hardest part due to the thickness of the layers...  So I used a very long sturdy needle, extra heavy thread and a pair of pliers to make the task go easier..

Then I covered the black felt on the spine with the dog paw ribbon using again double sided interfacing.




Done....  I struggle with writing tutorials as it is easier to do something than write directions on how to do it... I strive it to make the process easily understood.  If there is any point that needs more clarification, please write me and I will update it....



4 comments:

sam21ski said...

Wow, this is brilliant, and looks pretty easy to follow - thanks for sharing how you did it. May have to do one of these for my pooch xx

Chyfey said...

Love it...Love the fact that it was about your dog....and its so bright and colourful.
I made one after my 2015 year of crazy quilting ,I don't back them block to block and ended up with a thick book .

FredaB said...

Good old Morris. You do such wonderful work and he doesn't even know it. Hugs

FredaB

Erica said...

What a wonderful book! I read your post on the fabric books group on facebook, this is just what I need! I’ve been looking for ideas on putting pages together. I have one question - when joining the two pages to make a section, were the edges topsewn, machine or hand?, or overlapped and sewn. I would think top sewn but then to attach to the spine you would be sewing through the joining stitches and I wonder how firm that would be. Yours is obviously very securely made and looks amazing!

Related Posts Plugin for WordPress, Blogger...

Popular Posts